Taking The Plunge-Diving In-Starting with Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project
Taking The Plunge-Diving In-Starting with Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project
Blog Article
This great article below on the subject of How to Install or Replace a Shower Drain is immensely stimulating. Give it a go and make your own personal final thoughts.
Upgrading a bathroom is one of the more popular residence renovation jobs. Managing the plumbing for draining your shower can be exceedingly simple unless you overdo.
Managing Your Own Shower Drain Installment Job
You can literally construct a collection agency for your brand-new shower, however you really require to think about it. Do you actually want to get into the issues of getting the sloping right, not to mention seeing to it every aspect of it is water resistant? And also I mean every element! It is a lot easier to simply purchase a pre-cast collection agency online or at your local Lowes, Home Depot or hardware store. Structure one might sound like a terrific concept, yet you will possibly really feel in different ways after a number of hours.
No matter how you deal with obtaining a pan, you should strive to make use of one that has the drainpipe situated in the exact same spot as the original frying pan. Relocating the drain pipes can be a job, specifically if the home builder utilized a distinct framing framework. If you are identified to move the drain, you are going to need to cut back the pipeline or extend it, which may imply ripping up big chunks of the floor. Rephrase, you are going to be looking at a several weekend break job.
Presuming we have our drainpipe lined up, the real connect is fairly easy. The drainage pipe must be encountering upright approximately the collector. It will certainly often resemble a "U", which means it acts as a cleanout to keep nasty scents from returning up from the drainpipe. To attach the drain, you are mosting likely to produce a water limited connection between a drain cap on the top of the pan and also the drainage pipe. Solutions vary, however you are normally going to do this by placing a combining item on the top of the drainage pipe. This is after that covered with gaskets and also actually screwed right into the drain cap. The drain cap need to function as a locknut, to wit, it screws straight onto the coupling.
The complicated part of this procedure is obtaining your drainpipe cap to suit a watertight position in the pan. This is completed by backing off the drainpipe cap when you make sure everything fits together. At that point, you put plumbing technicians putty around the underside of the cap and after that screw it back on. The putty ought to develop a tight seal between the cap and also the shower pan, which maintains water from dripping under it and also right into the framing under the shower.
Certainly, bathroom showers been available in a wide array of styles nowadays. If you acquire a collector, they often featured plumbing directions or the store can note anything unusual you must know. It sounds intricate, but is generally quite direct. Have a good time!
Whether you are a tub or shower individual, many people try to find shower just options when buying a home. This simple reality suggests greater than a few property owners spend a weekend updating or setting up showers in their restrooms. Fortunately for you, it is a fairly straightforward process.
An enthusiast or frying pan refers to the horizontal surface situated at the end of the shower. The collection agency usually contains a non-slip surface area slightly banked in the direction of the center or any place the drainpipe lies. Integrated with 3 to 4 inch walls around the side, the goal of your shower water drainage plumbing is to obtain the water to move to as well as away.
Things to Know Before Installing a Shower Drain
Replacing a shower drain isn’t usually a difficult task, but it always pays to be prepared for complications before you start the job, especially as every project is different. While it should take just a couple of hours to replace a drain in a preformed shower base, you’ll want to allow yourself additional time and a flexible toolbox.
“As the age of the shower increases, so does the likelihood of problems during installation,” says Daniel O’Brian, the technical expert for leading online plumbing retailer SupplyHouse.com. Over time, older metal drains can corrode, making them very difficult to remove, and you can even run into problems with installations in newer showers if access to the drain is restricted. No matter what challenges you face, the following tips will help the project go a little more easily.
Prepare for pipe size discrepancies.
The majority of shower drainpipes are two inches in diameter, but if you have two-inch drains and you run into a three-inch drainpipe, you’ll be making another trip to the plumbing supply store. “Always check with local codes,” O’Brian suggests. “The larger drain size minimizes the chance of a shower overflowing.” And if you keep a supply of size-adaptable shower drains on hand, such as the Oatey 2-Inch or 3-Inch PVC Shower Drain, the size discrepancy won’t slow you down at all. This weld-type drain fits either a two- or three-inch drainpipe. With a two-inch drainpipe, the body of the drain fits over the pipe; with a three-inch pipe, it fits inside. If your home has three-inch drainpipes, it pays to pick up a box of size-adaptable drains to have on hand.
Assume you’ll have to cut through the ceiling.
In most cases, you won’t be able to avoid cutting through the ceiling below the shower to gain access. “If a leak is present, you’ll probably have to replace the drywall on the ceiling below as well as the drain, and you should take care of it as soon as possible to minimize damage,” O’Brian says. Drywall replacement is a relatively simple home repair project, so cutting a hole in the ceiling shouldn’t be a major concern. Alternatively, you can cover the hole with a return-air grill that can be easily removed if you need to access the plumbing at a future date.
The only time you won’t need to cut through the ceiling below the shower is when you’re replacing both the drain and the shower base. In that case, start by pulling out the old shower pan and removing the old drain. Then, connect the body of the new drain to the new shower base, and set the shower base in place according to the manufacturer’s specifications. Be warned: Balancing the shower base while you align the drain body over the pipe will almost certainly require the help of an additional person.
The best type of drain for this situation is often called a “compression,” or “friction,” drain, such as this Oatey 2-Inch PVC No-Calk Shower Drain, which features a rubber gasket inside the drain body. Remove the gasket before the shower base is set. After the shower base is set, lubricate the gasket with plumber’s soap and slide it into place between the drain body and the pipe. Tighten the compression nut inside the drain body with a screwdriver to seal the connection, then snap the strainer into place. Being able to remove the gasket before you set the shower base gives you a little more room to maneuver—remember, you’re balancing the shower base while you’re trying to fit the connected drain body over the pipe in the floor.
Tight spots spell trouble.
It doesn’t happen often, but occasionally when you cut through the ceiling below the shower you find wiring or pipes that prevent you from getting your water pump pliers firmly on the nut that connects the drain to the pipe. (These additional wires, pipes, and even ductwork would have been added after the shower was installed.) If you can’t find a way to remove the nut or reach the pipe to cut it below the drain, you may end up having to pull the shower base out so you can access the drain from the top. Then, just like that, what should have been a simple drain replacement turns into a major project.
While you may be stuck with this unanticipated problem, you can prevent it from happening in the future by installing an outer locknut-style drain, such as the Sioux Chief 2-Inch JackRabbit Shower Drain .
Unlike standard drains that solvent weld or attach with a nut, the JackRabbit drain attaches via four jacking screws from below. (It’s usually much easier to get a screwdriver in a tight spot where bulky water pump pliers won’t fit.) The drain body features a push-on compression gasket that attaches to the drainpipe without the need for caulking. After the shower base is set, tighten the jacking screws from below to suck the flange downward until it seals against the shower floor.
Sometimes it’s easier to replace the whole trap.
Whenever you’re installing a shower drain with welded connections, you have to cut the drainpipe to remove the old drain. While this is necessary, it leaves you with a shortened drainpipe that you’ll need to extend before you can install the new drain. Trying to extend the pipe while you’re working overhead in a tight space is both time-consuming and physically challenging, so it’s often quicker (and simpler) just to cut out the entire drain trap and replace it. To install another weld-type drain, such as this 2-Inch Sioux Chief PVC Drain, you’ll want to assemble and dry fit all the connections before you glue them together. Be sure the angle of fall on the horizontal drain pipe remains the standard ¼ inch per linear foot.
Take care not to block weep holes.
Installing a new drain in a tiled shower is another scenario that often necessitates replacing the entire shower floor. Tiled showers rest on a mortar bed laid over a waterproof membrane (such as the Oatey 5’ x 6’ PVC Shower Pan Liner) that’s installed over yet another mortar bed. Because of this construction, a cemented-in shower drain cannot be replaced unless the tiles and the mortar around it are also removed and then reconstructed.
Tiled showers offer another complication: Because grout can crack, it’s important to have a backup plan to catch any water that might leak through. For that reason, shower drains designed for installation in tiled showers should have weep holes in their middle section to direct any water that reaches the membrane into the shower drain. These applications require a drain that has weep holes, such as the Oatey 2-Inch or 3-Inch PVC Shower Drain. To install, attach the base of the three-part drain to the drainpipe before the first mortar bed is smoothed into place. Then, install the membrane over the mortar bed (and over the drain base) and cut out a section over the drain hole in order to attach the center part of the drain, on which the weep holes are located. Make sure the section with the weep holes does not get clogged with mortar. To ensure that water will be able to flow through the weep holes, place several handfuls of pea gravel around the base of the exposed drain to protect it from the next layer of mortar. If you take these precautions, once the shower floor has been tiled, any water that makes its way to the membrane will exit through the weep holes and down the drain rather than leak out elsewhere.
https://blog.supplyhouse.com/5-things-to-know-before-installing-a-shower-drain/
I'm certainly very taken with How to Install or Replace a Shower Drain and I hope you enjoyed the new blog posting. Be sure to take the time to distribute this entry if you appreciated it. Thank you for your time invested reading it.
Report this page